검색결과
-
[특집-기술위원회] TC 218 - 목재(Timber)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~107 △1963년 TC 108~111 △1964년 TC 112~115, TC 117 △1965년 TC 118 △1966년 TC 119~122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146~150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~161 △1975년 TC 162~164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171~174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~186 △1984년 TC 188 △1985년 TC 189~191 △1988년 TC 192~194 △1989년 TC 195 △1990년 TC 197, TC 198 △1991년 TC 199, TC 201, TC 202 △1992년 TC 204~206 △1993년 TC 209 △1994년 TC 210, TC 211 △1996년 TC 213, TC 214 등이 있다.ISO/TC 218 목재(Timber)와 관련된 기술위원회는 TC 215, TC 216, TC 217과 마찬가지로 1998년 결성됐다. 사무국은 우크라이나 표준화센터(Ukrainian Scientific Research and Training Center for Standardization, Certification and Quality Problems, UkrNDNC)에서 맡고 있다.위원회는 옥사나 삭(Mrs Oksana Sak)이 책임지고 있다. 현재 의장은 올렉시 치칠리아노(Mr Oleksii Tsytsyliano)이며 임기는 2025년 말까지다. ISO 기술 프로그램 관리자는 안나 카테리나 로시(Dr Anna Caterina Rossi), ISO 편집 관리자는 빈센조 바주치(M Vincenzo Bazzucchi) 등이다.범위는 용어, 사양 및 테스트 방법을 포함해 모든 용도에 사용되는 원형 목재, 제재목 및 가공 목재와 목재 재료의 표준화다. 단, ISO/TC 165 목재 구조물에 포함된 목재의 용도는 제외한다.현재 ISO/TC 218 사무국의 직접적인 책임 하에 발행된 표준은 53개며 ISO/TC 218 사무국의 직접적인 책임 하에 개발 중인 표준은 2개다. 참여하고 있는 회원은 23개국, 참관 회원은 40개국이다.□ ISO/TC 218 사무국의 직접적인 책임 하에 발행된 표준 53개 중 15개 목록▷ISO 631:1975 Mosaic parquet panels — General characteristics▷ISO 737:1975 Coniferous sawn timber — Sizes — Methods of measurement▷ISO 1029:1974 Coniferous sawn timber — Defects — Classification▷ISO 1030:1975 Coniferous sawn timber — Defects — Measurement▷ISO 1031:1974 Coniferous sawn timber — Defects — Terms and definitions▷ISO 1072:1975 Solid wood parquet — General characteristics▷ISO 2036:1976 Wood for manufacture of wood flooring — Symbols for marking according to species▷ISO 2299:1973 Sawn timber of broadleaved species — Defects — Classification▷ISO 2300:1973 Sawn timber of broadleaved species — Defects — Terms and definitions▷ISO 2301:1973 Sawn timber of broadleaved species — Defects — Measurement▷ISO 3129:2019 Wood — Sampling methods and general requirements for physical and mechanical testing of small clear wood specimens▷ISO 4470:1981 Sawn timber — Determination of the average moisture content of a lot▷ISO 4471:1982 Wood — Sampling sample trees and logs for determination of physical and mechanical properties of wood in homogeneous stands▷ISO 4472:1983 Coniferous and broadleaved sawn timber — Transportation packages▷ISO 4475:1989 Coniferous and broadleaved tree sawlogs — Visible defects — Measurement□ ISO/TC 218 사무국의 직접적인 책임 하에 개발 중인 표준 2개 목록▷ISO/CD 13061-15 Physical and mechanical properties of wood — Test methods for small clear wood specimens — Part 15: Determination of radial and tangential swelling▷ISO/CD 13061-16 Physical and mechanical properties of wood — Test methods for small clear wood specimens — Part 16: Determination of volumetric swelling
-
[특집-기술위원회] TC 211 - 지리정보/지리학(Geographic information/Geomatics)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~107 △1963년 TC 108~111 △1964년 TC 112~115, TC 117 △1965년 TC 118 △1966년 TC 119~122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146~150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~161 △1975년 TC 162~164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171~174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~186 △1984년 TC 188 △1985년 TC 189~191 △1988년 TC 192~194 △1989년 TC 195 △1990년 TC 197, TC 198 △1991년 TC 199, TC 201, TC 202 △1992년 TC 204~206 △1993년 TC 209 등이 있다.ISO/TC 211지리정보/지리학(Geographic information/Geomatics)과 관련된 기술위원회는 TC 210과 마찬가지로 1994년 결성됐다. 사무국은 스웨덴 국립표준청(Svenska institutet för standarder, SIS)에서 맡고 있다.위원회는 마츠 올린(Mr Mats Åhlin)가 책임지고 있다. 현재 의장은 피터 파슬로(Mr Peter Parslow)이며 임기는 2024년말까지다. ISO 기술 프로그램 관리자는 하킴 음킨시(Mr Hakim Mkinsi), ISO 편집 관리자는 앨리슨 레이드 자몬드(Ms Alison Reid-Jamond) 등이다.범위는 디지털 지리정보 분야의 표준화다. 지구와 관련된 위치와 직간접적으로 연관된 물체나 현상에 관한 정보에 대한 구조화된 표준 세트 확립을 목표로 하고 있다.지리 정보의 범위 내에서 이러한 표준은 데이터 관리를 위한 방법, 도구 및 서비스를 지정할 수 있다. 데이터 관리는 사용자 및 시스템을 위한 데이터 획득, 처리, 분석, 접근, 제시 및 출판이 포함된다.이 작업은 가능한 경우 정보 기술 및 데이터에 대한 적절한 표준과 연결되어야 하며 지리 데이터를 사용하는 부문별 응용 프로그램 개발을 위한 프레임워크를 제공해야 된다.현재 ISO/TC 211 사무국의 직접적인 책임 하에 발행된 표준은 97개며 ISO/TC 211 사무국의 직접적인 책임 하에 개발 중인 표준은 26개다. 참여하고 있는 회원은 38개국, 참관 회원은 35개국이다.□ ISO/TC 211 사무국의 직접적인 책임 하에 발행된 표준 97개 중 15개 목록▷ISO 6709:2022 Standard representation of geographic point location by coordinates▷ISO 19101-1:2014 Geographic information — Reference model — Part 1: Fundamentals▷ISO 19101-2:2018 Geographic information — Reference model — Part 2: Imagery▷ISO 19103:2015 Geographic information — Conceptual schema language▷ISO 19104:2016 Geographic information — Terminology▷ISO 19105:2022 Geographic information — Conformance and testing▷ISO 19106:2004 Geographic information — Profiles▷ISO 19107:2019 Geographic information — Spatial schema▷ISO 19108:2002 Geographic information — Temporal schema▷ISO 19108:2002/Cor 1:2006 Geographic information — Temporal schema — Technical Corrigendum 1▷ISO 19109:2015 Geographic information — Rules for application schema▷ISO 19110:2016 Geographic information — Methodology for feature cataloguing▷ISO 19111:2019 Geographic information — Referencing by coordinates▷ISO 19111:2019/Amd 1:2021 Geographic information — Referencing by coordinates — Amendment 1▷ISO 19111:2019/Amd 2:2023 Geographic information — Referencing by coordinates — Amendment 2□ ISO/TC 211 사무국의 직접적인 책임 하에 개발 중인 표준 26개 중 15개 목록▷ISO/DIS 19103 Geographic information — Conceptual schema language▷ISO/CD 19109 Geographic information — General feature model and rules for application schema▷ISO/AWI TR 19115-4 Geographic information – Metadata — Part 4: JSON schema implementation of metadata fundamentals▷ISO/DIS 19116 Geographic information — Positioning services▷ISO/AWI TR 19121 Geographic information — Imagery and gridded data▷ISO/AWI 19123-2 Geographic information — Schema for coverage geometry and functions — Part 2: Coverage implementation schema▷ISO/AWI TS 19123-4 Geographic information — Schema for coverage geometry and functions — Part 4: Tiling Schema▷ISO/AWI TS 19124-2 Geographic information — Calibration and validation of remote sensing data and derived products — Part 2: SAR▷ISO/AWI 19127 Geographic information — Geodetic register▷ISO/AWI TS 19130-2 Geographic information — Imagery sensor models for geopositioning — Part 2: SAR, InSAR, lidar and sonar▷ISO/CD 19135 Geographic information registration — Requirements▷ISO/DTS 19144-3 Geographic information — Classification systems — Part 3: Land Use Meta Language (LUML)▷ISO/DIS 19152-2 Geographic information — Land Administration Domain Model (LADM) — Part 2: Land registration▷ISO/FDIS 19152-3 Geographic information — Land Administration Domain Model (LADM) — Part 3: Marine georegulation▷ISO/DIS 19152-4 Geographic information — Land Administration Domain Model (LADM) — Part 4: Valuation information
-
[특집-기술위원회] TC 209 - 클린룸 및 관련 제어 환경(Cleanrooms and associated controlled environments)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~107 △1963년 TC 108~111 △1964년 TC 112~115, TC 117 △1965년 TC 118 △1966년 TC 119~122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146~150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~161 △1975년 TC 162~164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171~174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~186 △1984년 TC 188 △1985년 TC 189~191 △1988년 TC 192~194 △1989년 TC 195 △1990년 TC 197, TC 198 △1991년 TC 199, TC 201, TC 202 △1992년 TC 204~206 등이 있다.ISO/TC 209 클린룸 및 관련 제어 환경(Cleanrooms and associated controlled environments)과 관련된 기술위원회는 TC 207과 마찬가지로 1993년 결성됐다. 사무국은 미국 표준협회(American National Standards Institute, ANSI)에서 맡고 있다.위원회는 로버트 미엘케(Mr Robert Mielke)가 책임지고 있다. 현재 의장은 고든 엘리(Mr Gordon Ely)이며 임기는 2026년말까지다. ISO 기술 프로그램 관리자는 마호 타카하시(Mme Maho Takahashi), ISO 편집 관리자는 아룬 ABY 파라에카틸(Mr Arun ABY Paraecattil) 등이다.범위는 시설, 지속 가능성, 장비, 프로세스 및 운영과 관련된 기타 속성 및 특성 뿐 아니라 청결도를 제어하기 위한 클린룸 및 관련 제어 환경에 대한 표준화다.현재 ISO/TC 209 사무국의 직접적인 책임 하에 발행된 표준은 20개며 ISO/TC 209 사무국의 직접적인 책임 하에 개발 중인 표준은 3개다. 참여하고 있는 회원은 26개국, 참관 회원은 22개국이다.□ ISO/TC 209 사무국의 직접적인 책임 하에 발행된 표준 20개 중 15개 목록▷ISO 14644-1:2015 Cleanrooms and associated controlled environments — Part 1: Classification of air cleanliness by particle concentration▷ISO 14644-2:2015 Cleanrooms and associated controlled environments — Part 2: Monitoring to provide evidence of cleanroom performance related to air cleanliness by particle concentration▷ISO 14644-3:2019 Cleanrooms and associated controlled environments — Part 3: Test methods▷ISO 14644-4:2022 Cleanrooms and associated controlled environments — Part 4: Design, construction and start-up▷ISO 14644-5:2004 Cleanrooms and associated controlled environments — Part 5: Operations▷ISO 14644-7:2004 Cleanrooms and associated controlled environments — Part 7: Separative devices (clean air hoods, gloveboxes, isolators and mini-environments)▷ISO 14644-8:2022 Cleanrooms and associated controlled environments — Part 8: Assessment of air cleanliness by chemical concentration (ACC)▷ISO 14644-9:2022 Cleanrooms and associated controlled environments — Part 9: Assessment of surface cleanliness for particle concentration▷ISO 14644-10:2022 Cleanrooms and associated controlled environments — Part 10: Assessment of surface cleanliness for chemical contamination▷ISO 14644-12:2018 Cleanrooms and associated controlled environments — Part 12: Specifications for monitoring air cleanliness by nanoscale particle concentration▷ISO 14644-13:2017 Cleanrooms and associated controlled environments — Part 13: Cleaning of surfaces to achieve defined levels of cleanliness in terms of particle and chemical classifications▷ISO 14644-14:2016 Cleanrooms and associated controlled environments — Part 14: Assessment of suitability for use of equipment by airborne particle concentration▷ISO 14644-15:2017 Cleanrooms and associated controlled environments — Part 15: Assessment of suitability for use of equipment and materials by airborne chemical concentration▷ISO 14644-16:2019 Cleanrooms and associated controlled environments — Part 16: Energy efficiency in cleanrooms and separative devices▷ISO 14644-17:2021 Cleanrooms and associated controlled environments — Part 17: Particle deposition rate applications□ ISO/TC 209 사무국의 직접적인 책임 하에 개발 중인 표준 3개 목록▷ISO/AWI 14644-5 Cleanrooms and associated controlled environments — Part 5: Operations▷ISO/CD TS 14644-19 Cleanrooms and associated controlled environments — Part 19: General technical requirements of modular isolation units for emergency medical use▷ISO/AWI 14644-20 Cleanrooms and associated controlled environments — Part 20: Microbiological contamination control
-
[특집-기술위원회] TC 206 - 파인 세라믹(Fine ceramics)… 모든 형태의 파인 세라믹 재료 및 제품 분야 표준화스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 △1975년 TC 162~TC 164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171, TC 172, TC 173, TC 174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~TC 186 △1984년 TC 188 △1985년 TC 189, TC 190, TC 191 △1988년 TC 192~TC 194 △1989년 TC 195 △1990년 TC 197, TC 198 △1991년 TC 199, TC 201, TC 202 등이 있다.ISO/TC 206 파인 세라믹(Fine ceramics)과 관련된 기술위원회는 TC 204, TC 205와 마찬가지로 1992년 결성됐다. 사무국은 일본 산업표준조사회(日本産業標準調査会, Japanese Industrial Standards Committee, JISC)에서 맡고 있다.위원회는 히로유키 미야자키(Dr Hiroyuki Miyazaki)가 책임지고 있다. 현재 의장은 이희수 교수(Prof Heesoo Lee)가 맡고 있다.ISO 기술 프로그램 관리자는 츄안유 추(Ms Chuanyu Zou), ISO 편집 관리자는 아룬 ABY 파라에카틸(Mr Arun ABY Paraecattil) 등이다.범위는 모든 형태의 파인 세라믹 재료 및 제품 분야 표준화다. 기계, 열, 화학, 전기, 자기, 광학 및 이들의 조합을 포함한 특정 기능 응용 분야를 위한 분말, 단일체, 코팅 및 복합재 등 모든 형태를 포함하고 있다. 파인 세라믹이라는 용어는 특정 기능적 특성을 지닌 고도로 가공된 고성능, 주로 비금속 무기 재료로 정의된다.참고로 파인 세라믹의 대체 용어는 고급 세라믹, 엔지니어링 세라믹, 테크니컬 세라믹 또는 고성능 세라믹이다. 파인 세라믹(Fine ceramics)은 절연체·내열재·구조재로 쓸수 있도록 고도기술로 개발된 새로운 세라믹을 말한다.현재 ISO/TC 206 사무국의 직접적인 책임 하에 발행된 표준은 156개며 ISO/TC 206 사무국의 직접적인 책임하에 개발 중인 표준은 32개다. 참여하고 있는 회원은 13개국, 참관 회원은 22개국이다.□ ISO/TC 206 사무국의 직접적인 책임 하에 발행된 표준 156개 중 15개 목록▷ISO 3169:2023 Fine ceramics (advanced ceramics, advanced technical ceramics) — Methods for chemical analysis of impurities in aluminium oxide powders using inductively coupled plasma-optical emission spectrometry▷ISO 3180:2023 Fine ceramics (advanced ceramics, advanced technical ceramics) — Methods for chemical analysis of calcium-phosphate-based powders for non-biomedical applications▷ISO 4825-1:2023 Fine ceramics (advanced ceramics, advanced technical ceramics) --Test method for thermal property measurements of metalized ceramic substrates — Part 1: Evaluation of thermal resistance for use in power modules▷ISO 5189:2023 Fine ceramics (advanced ceramics, advanced technical ceramics) — Methods for chemical analysis of metal impurities in silicon dioxide powders using inductively coupled plasma-optical emission spectrometry▷ISO 5618-1:2023 Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for GaN crystal surface defects — Part 1: Classification of defects▷ISO 5712:2022 Fine ceramics (advanced ceramics, advanced technical ceramics) — Method for measuring the power generation characteristics of piezoelectric resonant devices for stand-alone power sources▷ISO 5722:2023 Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for determining tensile and shear creep of ceramic adhesive▷ISO 5803:2023 Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for determination of monoclinic phase in zirconia▷ISO/TS 6857:2024 Fine ceramics (advanced ceramics, advanced technical ceramics) — Physical properties of ceramic composites — Guidelines for determination of void and fibre contents in polished cross section by image analysis▷ISO 10676:2010 Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for water purification performance of semiconducting photocatalytic materials by measurement of forming ability of active oxygen▷ISO 10677:2011 Fine ceramics (advanced ceramics, advanced technical ceramics) — Ultraviolet light source for testing semiconducting photocatalytic materials▷ISO 10678:2010 Fine ceramics (advanced ceramics, advanced technical ceramics) — Determination of photocatalytic activity of surfaces in an aqueous medium by degradation of methylene blue▷ISO 11894-1:2013 Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for conductivity measurement of ion-conductive fine ceramics — Part 1: Oxide-ion-conducting solid electrolytes▷ISO 13124:2011 Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for interfacial bond strength of ceramic materials▷ISO 13125:2013 Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for antifungal activity of semiconducting photocatalytic materials□ ISO/TC 206 사무국의 직접적인 책임 하에 개발 중인 표준 32개 중 15개 목록▷ISO/CD 4255 Fine ceramics (advanced ceramics, advanced technical ceramics) — Mechanical properties of ceramic matrix composites at high temperature — Determination of axial tensile properties of tubes▷ISO/AWI 4825-2 Fine ceramics (advanced ceramics, advanced technical ceramics) --Test method for thermal property measurements of metalized ceramic substrates — Part 2: Evaluation of heat transfer characteristics for metalized ceramics substrate for power modules▷ISO/PRF 5618-2 Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for GaN crystal surface defects — Part 2: Method for determining etch pit density▷ISO/CD 5770 Fine ceramics (advanced ceramics, advanced technical ceramics) — Relative method for determining thermal conductivity of ceramic coatings▷ISO/DIS 10678 Fine ceramics (advanced ceramics, advanced technical ceramics) — Determination of photocatalytic activity of surfaces in an aqueous medium by degradation of methylene blue▷ISO/AWI 10820 Fine ceramics (advanced ceramics, advanced technical ceramics) — Ultraviolet irradiation equipment using UV-A LEDs and optical radiometry for performance test of semiconducting photocatalytic materials▷ISO/DIS 14544 Fine ceramics (advanced ceramics, advanced technical ceramics) — Mechanical properties of ceramic composites at high temperature — Determination of compressive properties▷ISO/DIS 14574 Fine ceramics (advanced ceramics, advanced technical ceramics) — Mechanical properties of ceramic composites at high temperature — Determination of tensile properties▷ISO/CD 14705 Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for hardness of monolithic ceramics at room temperature▷ISO/WD 15733 Fine ceramics (advanced ceramics, advanced technical ceramics) — Mechanical properties of ceramic composites at ambient temperature in air atmospheric pressure — Determination of tensile properties▷ISO/AWI 17138 Fine ceramics (advanced ceramics, advanced technical ceramics) — Mechanical properties of ceramic composites at room temperature — Determination of flexural strength▷ISO/AWI 17561 Fine ceramics (advanced ceramics, advanced technical ceramics) — Test methods for dynamic elastic moduli of monolithic ceramics at room temperature by sonic resonance and Impulse Excitation Technique (IET)▷ISO/CD 17590 Fine ceramics (advanced ceramics, advanced technical ceramics) — Methods of tests for reinforcements — Determination of the tensile properties of ceramic filaments at elevated temperature in air using the hot grip technique▷ISO/AWI 17947-1 Fine ceramics (advanced ceramics, advanced technical ceramics) — Methods for chemical analysis of fine silicon nitride powders — Part 1: Wet chemical methods, X-ray fluorescence (XRF) using the fused cast-bead method, carrier-gas hot extraction (CGHE) and combustion methods▷ISO/AWI 18719 Fine ceramics (advanced ceramics, advanced technical ceramics) — Methods for chemical analysis of impurities in yttrium oxide powders using inductively coupled plasma-optical emission spectrometry
-
[특집-기술위원회] TC 198 - 보건 의료 제품의 멸균(Sterilization of health care products)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 △1975년 TC 162~TC 164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171, TC 172, TC 173, TC 174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~TC 186 △1984년 TC 188 △1985년 TC 189, TC 190, TC 191 △1988년 TC 192~TC 194 △1989년 TC 195 등이 있다.ISO/TC 198 보건 의료 제품의 멸균(Sterilization of health care products)과 관련된 기술위원회는 TC 197과 마찬가지로 1990년 결성됐다. 사무국은 미국 표준협회(American National Standards Institute, ANSI)에서 맡고 있다.위원회는 아만다 베네딕(Ms Amanda Benedict)가 책임지고 있다. 현재 의장은 리차드 밴크로프트(Mr Richard Bancroft)이며 임기는 2025년 말까지다.ISO 기술 프로그램 관리자는 페트리샤 쿡(Mme Patricia Cook), ISO 편집 관리자는 클라우디아 루에제(Ms Claudia Lueje)등이다. 범위는 보건의료 제품의 멸균을 위한 프로세스 및 장비의 표준화다.현재 ISO/TC 198 사무국의 직접적인 책임 하에 발행된 표준은 69개며 ISO/TC 198 사무국의 직접적인 책임 하에 개발 중인 표준은 15개다. 참여하고 있는 회원은 34개국, 참관 회원은 21개국이다.□ ISO/TC 198 사무국의 직접적인 책임 하에 발행된 표준 69개 중 15개 목록▷ISO/TS 5111:2022 Guidance on quality of water for sterilizers, sterilization and washer-disinfectors for health care products▷ISO 11135:2014 Sterilization of health-care products — Ethylene oxide — Requirements for the development, validation and routine control of a sterilization process for medical devices▷ISO 11135:2014/Amd 1:2018 Sterilization of health-care products — Ethylene oxide — Requirements for the development, validation and routine control of a sterilization process for medical devices — Amendment 1: Revision of Annex E, Single batch release▷ISO 11137-1:2006 Sterilization of health care products — Radiation — Part 1: Requirements for development, validation and routine control of a sterilization process for medical devices▷ISO 11137-1:2006/Amd 1:2013 Sterilization of health care products — Radiation — Part 1: Requirements for development, validation and routine control of a sterilization process for medical devices — Amendment 1▷ISO 11137-1:2006/Amd 2:2018 Sterilization of health care products — Radiation — Part 1: Requirements for development, validation and routine control of a sterilization process for medical devices — Amendment 2: Revision to 4.3.4 and 11.2▷ISO 11137-2:2013 Sterilization of health care products — Radiation — Part 2: Establishing the sterilization dose▷ISO 11137-2:2013/Amd 1:2022 Sterilization of health care products — Radiation — Part 2: Establishing the sterilization dose — Amendment 1▷ISO 11137-3:2017 Sterilization of health care products — Radiation — Part 3: Guidance on dosimetric aspects of development, validation and routine control▷ISO/TS 11137-4:2020 Sterilization of health care products — Radiation — Part 4: Guidance on process control▷ISO 11138-1:2017 Sterilization of health care products — Biological indicators — Part 1: General requirements▷ISO 11138-2:2017 Sterilization of health care products — Biological indicators — Part 2: Biological indicators for ethylene oxide sterilization processes▷ISO 11138-3:2017 Sterilization of health care products — Biological indicators — Part 3: Biological indicators for moist heat sterilization processes▷ISO 11138-4:2017 Sterilization of health care products — Biological indicators — Part 4: Biological indicators for dry heat sterilization processes▷ISO 11138-5:2017 Sterilization of health care products — Biological indicators — Part 5: Biological indicators for low-temperature steam and formaldehyde sterilization processes□ ISO/TC 198 사무국의 직접적인 책임 하에 개발 중인 표준 15개 목록▷ISO/DIS 11135.2 Sterilization of health care products — Ethylene oxide — Requirements for the development, validation and routine control of a sterilization process for medical devices▷ISO/FDIS 11137-1 Sterilization of health care products — Radiation — Part 1: Requirements for the development, validation and routine control of a sterilization process for medical devices▷ISO/CD 11140-3 Sterilization of health care products — Chemical indicators — Part 3: Class 2 indicator systems for use in the Bowie and Dick-type steam penetration test▷ISO/CD 11140-4 Sterilization of health care products — Chemical indicators — Part 4: Class 2 indicators as an alternative to the Bowie and Dick-type test for detection of steam penetration▷ISO/CD 11140-5 Sterilization of health care products — Chemical indicators — Part 5: Class 2 indicators for Bowie and Dick-type air removal tests▷ISO/AWI 11607-3 Packaging for terminally sterilized medical devices — Part 3: Requirements for process development for forming, sealing and assembly▷ISO/AWI 11737-1 Sterilization of health care products — Microbiological methods — Part 1: Determination of a population of microorganisms on products▷ISO/FDIS 15883-1 Washer-disinfectors — Part 1: General requirements, terms and definitions and tests▷ISO/DIS 15883-2 Washer-disinfectors — Part 2: Requirements and tests for washer-disinfectors employing thermal disinfection for critical and semi-critical medical devices▷ISO/DIS 15883-3 Washer-disinfectors — Part 3: Requirements and tests for washer-disinfectors employing thermal disinfection for human waste containers▷ISO/CD 15883-6 Washer-disinfectors — Part 6: Requirements and tests for washer-disinfectors employing thermal disinfection for noncritical medical devices and health care equipment▷ISO/DIS 15883-7 Washer-disinfectors — Part 7: Requirements and tests for washer-disinfectors employing chemical disinfection for non-critical thermolabile medical devices and health care equipment▷ISO/AWI TS 17664-3 Processing of health care products — Information to be provided by the medical device manufacturer for the processing of medical devices — Part 3: Guidance on the designation of a reusable medical device to a quantitative cleaning classification▷ISO 17665 Sterilization of health care products — Moist heat — Requirements for the development, validation and routine control of a sterilization process for medical devices▷ISO/AWI 19253 Sterilization of health care products — Application of ISO/TS 22421 to the requirements for sterilizers used for the terminal sterilization of health care products containing aqueous liquid in sealed containers
-
[특집-기술위원회] TC 195 - 건축 기계 및 장비(Building construction machinery and equipment)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 △1975년 TC 162~TC 164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171, TC 172, TC 173, TC 174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~TC 186 △1984년 TC 188 △1985년 TC 189, TC 190, TC 191 △1988년 TC 192~TC 194 등이 있다.ISO/TC 195 건축 기계 및 장비(Building construction machinery and equipment)와 관련된 기술위원회는 1989년 결성됐다. 사무국은 중국 국가표준화관리위원회(国家标准化管理委员会, Standardization Administration of the P. R. C, SAC)에서 맡고 있다.위원회는 솽 리우(Mr Shuang LIU)가 책임지고 있다. 현재 의장은 징 리(Ms Jing Li)이며 임기는 2025년 말까지다. ISO 기술 프로그램 관리자는 몬자 코르터(Ms Monja Korter), ISO 편집 관리자는 이본느 헨(Mrs Yvonne Chen)등이다. 범위는 아래 내용을 포함한 건설 현장에서 사용되는 기계 및 장비 분야의 표준화다.표준화에 포함되는 내용은 △콘크리트 기계(예: 배처, 믹서, 펌프, 분무기, 운송, 진동기, 플로팅) △기초 기계(예: 말뚝 박기, 다이어프램 벽 설치, 흙 천공, 분사, 그라우팅, 토양 및 암석 혼합물용 드릴 장비) △골재 처리 기계(예: 스크리닝, 파쇄) △도로 건설 및 유지 관리 기계 및 장비 △터널 굴착 기계(TBM) 및 관련 기계 및 장비[예: 차폐 터널 보링 머신, 비차폐 터널 보링 머신, 텔레스코픽 쉴드 머신, 리머 머신, 마이크로 터널링 머신, 스러스트 보링 머신, 오거 보링 머신(채광용 제외), 에어록, TBM용 구조 챔버, 터널 보링 멀티서비스 차량(MSV)] △비계 등이다.또한 건축 자재의 생산 및 가공은 △자연석의 세공 △미세하고 무거운 점토 및 내화 세라믹 제조 △판유리, 중공유리, 특수유리의 생산, 처리, 가공 △현장에서 건축 자재를 처리하는 기계 및 장비 △도로 운영 기계 및 장비와 관련 서비스 △명명법 △애플리케이션 △분류 △평가 △기술 요구 사항 △테스트 방법 △안전 요구 사항 등을 포함한다.단, 고체 광물 물질 추출용 장비[예: 로드 헤더, 연속 광부, 착암기, 인상 천공기, 고벽 광부, LHD, 광산 오거 천공기), RMDS(신속 광산 개발 시스템)(ISO/TC 82)], 크레인(ISO/TC 96), 토공 기계 (ISO / TC 127), 승강 작업 플랫폼(ISO/TC 214), 건축 및 토목 공사(ISO/TC 59) 등은 제외한다.현재 ISO/TC 195 사무국과 관련해 발행된 표준은 39개며 ISO/TC 195 사무국의 직접적인 책임 하에 발행된 표준은 21개다.ISO/TC 195 사무국과 관련해 개발 중인 표준은 21개며 ISO/TC 195 사무국의 직접적인 책임 하에 개발 중인 표준은 8개다. 참여하고 있는 회원은 17개국, 참관 회원은 17개국이다.□ ISO/TC 195 사무국의 직접적인 책임 하에 발행된 표준 21개 중 15개 목록▷ISO 11375:1998 Building construction machinery and equipment — Terms and definitions▷ISO/TR 12603:2010 Building construction machinery and equipment — Classification▷ISO 15642:2003 Road construction and maintenance equipment — Asphalt mixing plants — Terminology and commercial specifications▷ISO 15643:2020 Road construction and maintenance equipment — Bituminous binder sprayers and synchronous bituminous binder sprayers-chip spreaders — Terminology and commercial specifications▷ISO 15644:2002 Road construction and maintenance equipment — Chippings spreaders — Terminology and commercial specifications▷ISO 15645:2018 Road construction and maintenance equipment — Road milling machinery — Terminology and commercial specifications▷ISO 15688:2012 Road construction and maintenance equipment — Soil stabilizers — Terminology and commercial specifications▷ISO 15689:2003 Road construction and maintenance equipment — Powder binder spreaders — Terminology and commercial specifications▷ISO 15878:2021 Road construction and maintenance equipment — Paver-finishers — Commercial specifications▷ISO 16039:2004 Road construction and maintenance equipment — Slipform pavers — Definitions and commercial specifications▷ISO 16039:2004/Amd 1:2013 Road construction and maintenance equipment — Slipform pavers — Definitions and commercial specifications — Amendment 1▷ISO 19432-1:2020 Building construction machinery and equipment — Portable, hand-held, internal combustion engine-driven abrasive cutting machines — Part 1: Safety requirements for cut-off machines for centre-mounted rotating abrasive wheels▷ISO 19433:2008 Building construction machinery and equipment — Pedestrian-controlled vibratory plates — Terminology and commercial specifications▷ISO 19452:2008 Building construction machinery and equipment — Pedestrian-controlled vibratory (percussion) rammers — Terminology and commercial specifications▷ISO 19452:2008/Cor 1:2008 Building construction machinery and equipment — Pedestrian-controlled vibratory (percussion) rammers — Terminology and commercial specifications — Technical Corrigendum 1□ ISO/TC 195 사무국의 직접적인 책임 하에 개발 중인 표준 8개 목록▷ISO/AWI 19432-2 Building construction machinery and equipment — Portable, hand-held, internal combustion engine-driven abrasive cutting machines — Part 2: Machines for abrasive chains — Safety requirements▷ISO/FDIS 20500-1 Mobile road construction machinery — Safety — Part 1: Common requirements▷ISO/FDIS 20500-2 Mobile road construction machinery — Safety — Part 2: Specific requirements for road-milling machines▷ISO/FDIS 20500-3 Mobile road construction machinery — Safety — Part 3: Specific requirements for soil-stabilising machines and recycling machines▷ISO/FDIS 20500-4 Mobile road construction machinery — Safety — Part 4: Specific requirements for compaction machines▷ISO/FDIS 20500-5 Mobile road construction machinery — Safety — Part 5: Specific requirements for paver-finishers▷ISO/FDIS 20500-6 Mobile road construction machinery — Safety — Part 6: Specific requirements for mobile feeders▷ISO/FDIS 20500-7 Mobile road construction machinery — Safety — Part 7: Specific requirements for slipform pavers and related machines□ ISO/TC 195 사무국 분과위원회(Subcommittee)의 책임 하에 발행 및 개발 중인 표준 현황▷ISO/TC 195/SC 1 Machinery and equipment for concrete work ; 발행된 표준 14개, 개발 중인 표준 4개▷ISO/TC 195/SC 2 Road operation machinery and associated equipment ; 발행된 표준 1개, 개발 중인 표준 1개▷ISO/TC 195/SC 3 Drilling and foundation machinery and equipment ; 발행된 표준 3개, 개발 중인 표준 8개
-
[특집-기술위원회] TC 189 - 세라믹 타일(Ceramic tile)… 바닥재 및 벽면 마감재에 사용되는 세라믹 타일의 표준화스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 △1975년 TC 162~TC 164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171, TC 172, TC 173, TC 174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~TC 186, △1984년 TC 188등이 있다.ISO/TC 189 세라믹 타일(Ceramic tile)과 관련된 기술위원회는 1985년 결성됐다. 사무국은 미국 표준협회(American National Standards Institute, ANSI)에서 맡고 있다.위원회는 존 P. 샌더스(Dr John P. Sanders)이 책임지고 있다. 현재 의장은 노아 치티(Mr Noah Chitty)이며 임기는 2024년까지다.ISO 기술 프로그램 관리자는 안나 카테리나 로시(Dr Anna Caterina Rossi), ISO 편집 관리자는 루시 커크(Ms Lucy Kirk)등으로 조사됐다. 범위는 일반적으로 바닥재 및 벽면 마감재에 사용되는 세라믹 타일의 표준화다.현재 ISO/TC 189 사무국의 직접적인 책임 하에 발행된 표준은 35개며 ISO/TC 189 사무국의 직접적인 책임 하에 개발 중인 표준은 12개다. 참여하고 있는 회원은 35개국, 참관 회원은 25개국이다.□ ISO/TC 189 사무국의 직접적인 책임 하에 발행된 표준 35개 중 15개 목록▷ISO 10545-1:2014 Ceramic tiles — Part 1: Sampling and basis for acceptance▷ISO 10545-2:2018 Ceramic tiles — Part 2: Determination of dimensions and surface quality▷ISO 10545-3:2018 Ceramic tiles — Part 3: Determination of water absorption, apparent porosity, apparent relative density and bulk density▷ISO 10545-4:2019 Ceramic tiles — Part 4: Determination of modulus of rupture and breaking strength▷ISO 10545-5:1996 Ceramic tiles — Part 5: Determination of impact resistance by measurement of coefficient of restitution▷ISO 10545-5:1996/Cor 1:1997 Ceramic tiles — Part 5: Determination of impact resistance by measurement of coefficient of restitution — Technical Corrigendum 1▷ISO 10545-6:2010 Ceramic tiles — Part 6: Determination of resistance to deep abrasion for unglazed tiles▷ISO 10545-7:1996 Ceramic tiles — Part 7: Determination of resistance to surface abrasion for glazed tiles▷ISO 10545-8:2014 Ceramic tiles — Part 8: Determination of linear thermal expansion▷ISO 10545-9:2013 Ceramic tiles — Part 9: Determination of resistance to thermal shock▷ISO 10545-10:2021 Ceramic tiles — Part 10: Determination of moisture expansion▷ISO 10545-11:1994 Ceramic tiles — Part 11: Determination of crazing resistance for glazed tiles▷ISO 10545-12:1995 Ceramic tiles — Part 12: Determination of frost resistance▷ISO 10545-12:1995/Cor 1:1997 Ceramic tiles — Part 12: Determination of frost resistance — Technical Corrigendum 1▷ISO 10545-13:2016 Ceramic tiles — Part 13: Determination of chemical resistance□ ISO/TC 189 사무국의 직접적인 책임 하에 개발 중인 표준 12개 목록▷ISO/CD 10545-22 Ceramic tiles — Part 22: Determination of resistance to wear with a multi-attribute method▷ISO/CD 10545-23 Ceramic tiles — Part 23: Determination of elastic modulus for substrates and glaze layer▷ISO/WD 10545-24 Ceramic tiles — Part 24: Tensile adhesion strength of multilayer tiles and tile adhesives▷ISO/AWI 10545-25 Ceramic tiles — Part 25: Determination of reverse staining resistance▷ISO/AWI 13007-1 Ceramic tiles — Grouts and adhesives — Part 1: Terms, definitions and specifications for adhesives▷ISO/AWI 13007-3 Ceramic tiles — Grouts and adhesives — Part 3: Terms, definitions and specifications for grouts▷ISO/AWI 13007-7 Ceramic tiles — Grouts and adhesives — Part 7: Sound dampening materials for use beneath ceramic tiling bonded with adhesives — Requirements, test methods, evaluation of conformity, classification and designation▷ISO/AWI TR 17870-2 Ceramic tiles — Guidelines for installation — Part 2: Installation of thin ceramic wall and floor tiles and panels▷ISO/AWI 17889-3 Ceramic tiling systems — Sustainability for ceramic tiles and installation materials — Part 3: Guidelines for the application and verification of ISO 17889-1 and 17889-2▷ISO/WD 20355 Quantitative determination of antiviral activity of ceramic tile surfaces and survival of viruses on ceramic surfaces — Test methods — Ceramic tile surfaces with incorporated antiviral agents▷ISO/WD 20356 Quantitative determination of antifungal activity of ceramic tile surfaces — Test methods — Ceramic tile surfaces with incorporated antifungal agents▷ISO/WD 22267-1 Ceramic Tiling Systems — Embodied Carbon — Part 1: Calculation of Embodied Carbon of Ceramic Tile
-
[특집-기술위원회] TC 182 - 지반공학(Geotechnics)… 토양 및 암석의 특성을 포함해 건축 및 토목 공학 분야의 지반 공학적 측면의 표준화스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 △1975년 TC 162~TC 164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171, TC 172, TC 173, TC 174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 등이 있다.ISO/TC 182 지반공학(Geotechnics)과 관련된 기술위원회는 1981년 결성됐다. 사무국은 영국 표준협회(British Standards Institution, BSI)에서 맡고 있다.위원회는 디드레 푸리(Miss Deidre Fourie)가 책임지고 있으며 현재 의장은 존 파웰(Mr John Powell)이다. ISO 기술 프로그램 관리자는 안나 카테리나 로시(Dr Anna Caterina Rossi), ISO 편집 관리자는 앤 기엣(Ms Anne Guiet) 등으로 조사됐다.범위는 토양 및 암석의 (관련) 특성을 포함해 건축 및 토목 공학 분야의 지반 공학적 측면의 표준화다.현재 ISO/TC 182 사무국의 직접적인 책임 하에 발행된 표준은 58개며 ISO/TC 182 사무국의 직접적인 책임 하에 개발 중인 표준은 6개다. 참여하고 있는 회원은 25개국, 참관 회원은 31개국이다.□ ISO/TC 182 사무국의 직접적인 책임 하에 발행된 표준 58개 중 15개 목록▷ISO 14688-1:2017 Geotechnical investigation and testing — Identification and classification of soil — Part 1: Identification and description▷ISO 14688-2:2017 Geotechnical investigation and testing — Identification and classification of soil — Part 2: Principles for a classification▷ISO 14689:2017 Geotechnical investigation and testing — Identification, description and classification of rock▷ISO 17628:2015 Geotechnical investigation and testing — Geothermal testing — Determination of thermal conductivity of soil and rock using a borehole heat exchanger▷ISO 17892-1:2014 Geotechnical investigation and testing — Laboratory testing of soil — Part 1: Determination of water content▷ISO 17892-1:2014/Amd 1:2022 Geotechnical investigation and testing — Laboratory testing of soil — Part 1: Determination of water content — Amendment 1▷ISO 17892-2:2014 Geotechnical investigation and testing — Laboratory testing of soil — Part 2: Determination of bulk density▷ISO 17892-3:2015 Geotechnical investigation and testing — Laboratory testing of soil — Part 3: Determination of particle density▷ISO 17892-4:2016 Geotechnical investigation and testing — Laboratory testing of soil — Part 4: Determination of particle size distribution▷ISO 17892-5:2017 Geotechnical investigation and testing — Laboratory testing of soil — Part 5: Incremental loading oedometer test▷ISO 17892-6:2017 Geotechnical investigation and testing — Laboratory testing of soil — Part 6: Fall cone test▷ISO 17892-7:2017 Geotechnical investigation and testing — Laboratory testing of soil — Part 7: Unconfined compression test▷ISO 17892-8:2018 Geotechnical investigation and testing — Laboratory testing of soil — Part 8: Unconsolidated undrained triaxial test▷ISO 17892-9:2018 Geotechnical investigation and testing — Laboratory testing of soil — Part 9: Consolidated triaxial compression tests on water saturated soils▷ISO 17892-10:2018 Geotechnical investigation and testing — Laboratory testing of soil — Part 10: Direct shear tests□ ISO/TC 182 사무국의 직접적인 책임 하에 개발 중인 표준 6개 목록▷ISO/AWI 16383-1 Geotechnical investigation and testing — Laboratory testing of rock — Part 1: Determination of water content▷ISO/AWI 16383-2 Geotechnical investigation and testing — Laboratory testing of rock — Part 2: Determination of bulk density▷ISO/DIS 18674-7 Geotechnical investigation and testing — Geotechnical monitoring by field instrumentation — Part 7: Measurement of strains: Strain gauges▷ISO/AWI 18674-9 Geotechnical investigation and testing -Geotechnical monitoring by field instrumentation — Part 9: Measurement of displacements by geodetic means▷ISO 22476-16 Geotechnical investigation and testing — Field testing — Part 16: Borehole shear test▷ISO/WD 22477-6 Geotechnical investigation and testing — Testing of geotechnical structures — Part 6: Load testing of soil nails and rock bolts
-
[특집-기술위원회] TC 174 - 보석 및 귀금속(Jewellery and precious metals)… 번호 부여 시스템, 반지 크기, 귀금속 색상 및 코팅, 다이아몬드 등 주얼리스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 △1975년 TC 162~TC 164 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 등도 포함된다.ISO/TC 174 보석 및 귀금속(Jewellery and precious metals)과 관련된 기술위원회는 TC 171, TC 172, TC 173과 마찬가지로 1978년 결성됐다. 사무국은 독일 표준화기구(Deutsches Institut für Normung e.V., DIN)에서 맡고 있다.위원회는 페트라 비쇼프((FH) Petra Bischoff)가 책임지고 있으며 현재 의장은 조나단 조드리(Mr Jonathan Jodry)이며 임기는 2024년까지다.ISO 기술 프로그램 관리자는 블란딘 가르시아(Mme Blandine Garcia), ISO 편집 관리자는 빈센조 바주치(M Vincenzo Bazzucchi) 등으로 조사됐다.범위는 번호 부여 시스템, 반지 크기, 귀금속 색상 및 코팅, 다이아몬드 등 주얼리 분야와 분석, 샘플링, 불순물 등 귀금속 분야 표준화다.현재 ISO/TC 174 사무국의 직접적인 책임 하에 발행된 표준은 21개며 ISO/TC 173 사무국의 직접적인 책임 하에 개발 중인 표준은 10개다. 참여하고 있는 회원은 19개국, 참관 회원은 25개국이다.□ ISO/TC 174 사무국의 직접적인 책임 하에 발행된 표준 21개 중 15개 목록▷ISO 5724:2023 Jewellery and precious metals — Determination of very high purity gold — Difference method using ICP-MS▷ISO 8653:2016 Jewellery — Ring-sizes — Definition, measurement and designation▷ISO 8654:2018 Jewellery — Colours of gold alloys — Definition, range of colours and designation▷ISO 8654:2018/Amd 1:2019 Jewellery — Colours of gold alloys — Definition, range of colours and designation — Amendment 1▷ISO 9202:2019 Jewellery and precious metals — Fineness of precious metal alloys▷ISO 10713:1992 Jewellery — Gold alloy coatings▷ISO 11210:2023 Jewellery and precious metals — Determination of platinum — Gravimetry using ammonium chloride▷ISO 11426:2021 Jewellery and precious metals — Determination of gold — Cupellation method (fire assay)▷ISO 11427:2014 Jewellery — Determination of silver in silver jewellery alloys — Volumetric (potentiometric) method using potassium bromide▷ISO 11490:2023 Jewellery and precious metals — Determination of palladium — Gravimetry using dimethylglyoxime▷ISO 11494:2019 Jewellery and precious metals — Determination of platinum in platinum alloys — ICP-OES method using an internal standard element▷ISO 11495:2019 Jewellery and precious metals — Determination of palladium in palladium alloys — ICP-OES method using an internal standard element▷ISO 11596:2021 Jewellery and precious metals — Sampling of precious metals and precious metal alloys▷ISO 13756:2015 Jewellery — Determination of silver in silver jewellery alloys — Volumetric (potentiometric) method using sodium chloride or potassium chloride▷ISO 15093:2020 Jewellery and precious metals — Determination of high purity gold, platinum and palladium — Difference method using ICP-OES□ ISO/TC 174 사무국의 직접적인 책임 하에 개발 중인 표준 10개 목록▷ISO/PRF 6893 Jewellery and precious metals — Inspection of batches of small diamonds — Terminology, classification and test methods▷ISO/DIS 10713 Jewellery and precious metals — Gold alloy coatings▷ISO/PRF 11427 Jewellery and precious metals — Determination of silver — Potentiometry using potassium bromide▷ISO/PRF 13756 Jewellery and precious metals — Determination of silver — Potentiometry using sodium chloride or potassium chloride▷ISO/DIS 18214 Jewellery and precious metals — Determination of high purity gold, silver, platinum and palladium — Difference method using SPARK-OES▷ISO/AWI 19376-1 Jewellery and precious metals — Vocabulary — Part 1: Precious metals and units▷ISO/CD 19919 Jewellery and precious metals — Determination of silver — ICP-OES method using an internal standard element▷ISO/AWI 21261-1 Jewellery and precious metals — Responsible precious metals — Part 1: General requirements for responsible precious metals▷ISO/AWI 21261-2 Jewellery and precious metals — Responsible precious metals — Part 2: Minimum rules and procedures for conformity assessment schemes▷ISO/AWI 21261-3 Jewellery and precious metals — Responsible precious metals — Part 3: Requirements for recycled gold
-
[특집-기술위원회] TC 173 - 보조 용품(Assistive products)… 개인의 줄어든 능력을 보정하는데 도움을 주기 위한 보조 용품 및 관련 서비스스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 △1975년 TC 162~TC 164 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 등도 포함된다.ISO/TC 173 보조 용품(Assistive products)과 관련된 기술위원회는 TC 171, TC 172와 마찬가지로 1978년 결성됐다. 사무국은 스웨덴 표준연구소(Swedish Institute for Standards, SIS)에서 맡고 있다.위원회는 조아킴 포크(Mr Joakim Falk)가 책임지고 있으며 현재 의장은 마리타 브런딘(Ms Marita Brundin)이며 임기는 2025년까지다. ISO 기술 프로그램 관리자는 마호 타카하시(Mme Maho Takahashi), ISO 편집 관리자는 발레리아 아가멤논(Ms Valeria Agamennone) 등으로 조사됐다.범위는 개인의 줄어든 능력을 보정하는데 도움을 주기 위한 보조 용품 및 관련 서비스 분야의 표준화다. 단 기타 기술위원회 및 시스템위원회에서 다루고 있는 보조용품들은 제외한다.교통 수단(ISO/TC 8, 20, 22), 건물 건축(ISO/TC 59), 가구(ISO/TC 136), 수술용 임플란트(ISO/TC 150), 보철물 및 교정 장치(ISO/TC 150)에 대한 접근 /TC 168), 광학 및 포토닉스(ISO/TC 172), 전기 안전(IEC/TC 62), 보청기(IEC/TC 29), ICT 기술(JTC 1) 및 인체공학에서 다루는 설계 원리(ISO/TC 159) 및 적극적 생활 지원(IEC SyCAAL) 등이 포함된다.현재 ISO/TC 173 사무국과 관련해 발행된 표준은 95개며 이 중 ISO/TC 173 사무국의 직접적인 책임 하에 발행된 표준은 24개다.ISO/TC 173 사무국과 관련해 개발 중인 표준은 22개며 ISO/TC 173 사무국의 직접적인 책임 하에 개발 중인 표준은 11개다. 참여하고 있는 회원은 26개국, 참관 회원은 29개국이다.□ ISO/TC 173 사무국의 직접적인 책임 하에 발행된 표준 24개 중 15개 목록▷ISO 10535:2021 Assistive products — Hoists for the transfer of persons — Requirements and test methods▷ISO 11199-1:2021 Assistive products for walking manipulated by both arms — Requirements and test methods — Part 1: Walking frames▷ISO 11199-2:2021 Assistive products for walking manipulated by both arms — Requirements and test methods — Part 2: Rollators▷ISO 11199-3:2005 Walking aids manipulated by both arms — Requirements and test methods — Part 3: Walking tables▷ISO 11334-1:2007 Assistive products for walking manipulated by one arm — Requirements and test methods — Part 1: Elbow crutches▷ISO 11334-4:1999 Walking aids manipulated by one arm — Requirements and test methods — Part 4: Walking sticks with three or more legs▷ISO/TR 11548-1:2001 Communication aids for blind persons — Identifiers, names and assignation to coded character sets for 8-dot Braille characters — Part 1: General guidelines for Braille identifiers and shift marks▷ISO/TR 11548-2:2001 Communication aids for blind persons — Identifiers, names and assignation to coded character sets for 8-dot Braille characters — Part 2: Latin alphabet based character sets▷ISO 17966:2016 Assistive products for personal hygiene that support users — Requirements and test methods▷ISO 19894:2019 Walking trolleys — Requirements and test methods▷ISO 20342-1:2022 Assistive products for tissue integrity when lying down — Part 1: General requirements▷ISO/TR 20342-7:2021 Assistive products for tissue integrity when lying down — Part 7: Foam properties, characteristics and performance▷ISO/TS 20342-10:2022 Assistive products for tissue integrity when lying down — Part 10: Guidance to cleaning, disinfecting and care of polyurethane APTI covers▷ISO 21801-1:2020 Cognitive accessibility — Part 1: General guidelines▷ISO 21801-2:2022 Cognitive accessibility — Part 2: Reporting□ ISO/TC 173 사무국의 직접적인 책임 하에 개발 중인 표준 11개 목록▷ISO 11199-2:2021/DAmd 1 Assistive products for walking manipulated by both arms — Requirements and test methods — Part 2: Rollators — Amendment 1: Eliminate brake requirements in 6.5 Structure requirements▷ISO/DIS 11334-4 Assistive products for walking, manipulated by one arm — Requirements and test methods — Part 4: Walking sticks with three or more legs▷ISO/CD 17966 Assistive products for toileting, bathing and showering — Requirements and test methods▷ISO/AWI TR 20342-2 Assistive products for tissue integrity when lying down — Part 2: Microclimate▷ISO/CD 20342-3 Assistive products for tissue integrity when lying down — Part 3: Strength and impact▷ISO/CD 20342-4 Assistive products for tissue integrity when lying down — Part 4: Durability▷ISO/DIS 20342-5 Assistive products for tissue integrity when lying down — Part 5: Resistance to cleaning and disinfection▷ISO/AWI 20342-6 Assistive products for tissue integrity when lying down — Part 6: Horizontal stiffness▷ISO/CD 20342-8 Assistive products for tissue integrity when lying down — Part 8: Pressure distribution▷IEC/DIS 80601-2-52 Medical electrical equipment — Part 2-52: Particular requirements for the basic safety and essential performance of medical beds▷IEC/DIS 80601-2-89 Medical electrical equipment — Part 2-89: Particular requirements for the basic safety and essential performance of medical beds for children□ ISO/TC 173 사무국 분과위원회(Subcommittee)의 책임 하에 발행 및 개발 중인 표준 현황▷ISO/TC 173/SC 1 Wheelchairs ; 발행된 표준 41개, 개발 중인 표준 6개▷ISO/TC 173/SC 2 Classification and terminology ; 발행된 표준 1개, 개발 중인 표준 0개▷ISO/TC 173/SC 3 Aids for ostomy and incontinence ; 발행된 표준 23개, 개발 중인 표준 4개▷ISO/TC 173/SC 7 Assistive products for persons with impaired sensory functions ; 발행된 표준 6개, 개발 중인 표준 1개